Beneficiation of kalabsha kaolin ore and its utilization in the manufacture of solid alum
Auteur(s):
Awadallah R M Ahmed Y D Mohamed A E
Date de publication:
2001
Référence bibliographique:
Beneficiation of kalabsha kaolin ore and its utilization in the manufacture of solid alum A E Mohamed R M Awadallah Y D AhmedThe Arabian journal for science and engineering المجلة العربية للعلوم والهندسة Univeristy of Petroleum and MineralsVol 26 no 2B (October 2001) p p 115126Mohamed A EAwadallah R MAhmed Y D
Résumé:
Twentyfour samples of kaolin ore were collected from the kaolin mine at Kalabsha
The samples were crushed and dry and wet screened into different particle sizes The
chemical analyses for SiO2 and AI2O3 indicate that the particle size of 7 to 0850 mm is
the most suitable as it gives the highest A12O3 % and the lowest SiO2 % compared to the
original samples The sample of 224 mm in size was subjected to attrition in tap water for
one hour The slime and solid residue were collected and passed through a set of sieves
The0075 mm fraction was cycloned to separate very fine particles (001 mm) Each
fraction was collected dried and analyzed The results indicate that the 001 mm particle
size yields the highest Al2O3 (3840%) and the lowest SiO2 (4350%) and Fe2O3 (090%)
compared to the original sample The solid alum was prepared from the roasted sample
(001 mm particle size) at 600°C for 30 minutes using concentrated H2SO4 with gentle
heating and stirring until white intensi ve fumes of H2SO4 evaporated
The present work is intended to beneficiate the kaolin ore of the Wadi Kalabsha area
employing the effect of dry screening and attrition followed by hydro cyclone to separate
very fine size particles for the manufacture of solid alum [Al2(SO4)3] The present study
indicates that 1337 ton of kaolin ore is beneficiated to produce 0526 ton for use in alum
production تم في هذا البحث دراسة خام الكاولين الموجود بمنطقة كلابشة وأوضحت النتائج أن خام الكاولين يتدرج في الجودة من الطبقات العليا إلى الطبقات السفلى حيث أثبتت التحاليل أن الخام المتواجد بأعلى طبقة ذو جودة منخفضة الرتبة بالنسبة للخام المتواجد أسفل الطبقة العلوية وأوضح التحليل الميكانيكي الجاف أن الجزء المنفصل ذو الحبيبات التي قطرها يساوي 085 مم يحتوي على أعلى نسبة من أكسيد الألومنيوم، أما التحليل الميكانيكي الرطب فقد ساعد في رفع نسبة أكسيد الألومنيوم وباستخدام الهيدروسيكلون وأوضحت النتائج أن الحبيبات ذات الحجم (001–001 مم) يمثلان أعلى رتبة من أكسيد الألومنيوم وأقل رتبة ن أكسيد الحديديك، تم تطبيق هذه النتائج في استخدام هذا الركاز في تحضير الشبه (كبريتات الألومنيوم) وأوضحت الدراسة أن التكاليف الكلية المعملية لإنتاج طن من الشبه هي 24654 جنيها حيث يستخدم 12337 طن من الخام (سعر طن الخام 28 جنيها، الذي يتم تركيزة ويعطي 0526 طنا من الحبيبات ذات الحجم001 مم (384 % ألومنيا)